Ge adora dryer service manual

Thermostats can be tested, repaired, or replaced, but it takes some electrical expertise to get the job done right. Timer motor: This little device does a big job, regulating how and when power is sent to each component. When the timing is out, you may find that the heating element does not heat up at the same time the drum is spinning.

That means warm-yet-still-damp laundry. Fortunately, the motor itself can usually be replaced without having to replace the entire motor assembly. If you have a fuse box, inspect the fuse panel to ensure no fuses are blown. Reset any circuit breakers or replace any blown fuses as needed. In this case, the dryer is shutting down to prevent overheating. The drive motor can either be cleaned or replaced as necessary. Clogged vent: If hot air is not venting properly, your dryer will overheat and shut down.

A clogged or kinked vent line is relatively easy to remedy, but a replacement part may be needed if damage has accrued over time. Thermal overload switch or fuse: If you're experiencing either of the two issues above, it's the thermal overload switch or fuse that shuts down the dryer to prevent further damage. However, this component itself can become damaged. If that's the case, it's vital to have this part inspected, repaired, or replaced by a trained professional. Moisture sensor: If your dryer has the ability to detect moisture and time its dry cycle accordingly, this part could be the culprit.

F or Mobile or Manufactured Home see section 1 1. In the state of Massachusetts. Installation must be performed by a qualified or. Ask a question. Related product manuals. What is a condenser dryer? A condenser dryer is a dryer in which condensation ends up in a reservoir. What is a drain dryer? A drain dryer is a dryer in which the warm air and condensation are drained through a hose.

What is the best thing to do about a smelly dryer? It is best to wipe the dryer drum with a damp cloth and some lemon cleaner. There is a burning smell from my dryer, now what? GE Appliances. Previous Page. Next Page. Stainless steel free-standing, drawer freezer refrigerator 16 pages. Side by side refrigerator 22, 23, 25 and 27 models pages.

Side by side refrigerators models 23, 25 and 27 pages. Double-door, bottom-drawer, free-standing refrigerators 29 pages. Page 2 If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened. This service guide may not be reproduced in whole or in part in any form without written permission from the General Electric Company.

Page 4 Ice Box Door Assembly Open freezer drawer, then lift and remove handles: freezer drawer. Handle design varies based on models, however, installation is the same. Page 13 Caution: In the following step, to prevent damage To install the left fresh food door: to door and electronics, carefully place the door in a Note: To close correctly to the cabinet, the hinge pin protected location.

Note: The lower door hinge pin and hinge are keyed 1. Locate tab in the center on the bottom and push in. Pull Dispenser Tray assembly out. Entering Demo Mode will be displayed. The lights and fans if previously operating will still operate, but the compressor will not operate. If no other key is touched, the display will show thermistor temperature.

About temperature adjustments Note: The LCD customer control does not incorporate pads for temperature adjustment. To change compartment temperatures, touch the screen to wake the control up and change temperatures directly on the LCD screen. Page 25 About dispenser selections When the customer changes the dispenser functions, the display will show a short animation of the dispenser selection.

Continued next page — 25 — When Turbo Freeze or Turbo Cool is selected, the set temperatures in the freezer and refrigerator are not changed. By selecting Precise Fill, the customer can select the amount of water. By selecting Auto Fill, the dispenser will function by the use of 4 ultrasonic sensors 2 sensors located below the base of the paddle and 2 sensors located in front of the dispenser funnel. Wake the screen. Simultaneously press and hold the Water, Cubed, and Precise Fill buttons for 5 seconds.

Sleep The display on the upper right should show the status of the sensors. Page 29 About Consumer System Settings When the consumer selects System Settings from the main screen, they can change or reset functions on the unit by scrolling thru the screens. Damper is mechanical and manually operated on GE models. Fresh Food Evaporator shown with evaporator cover removed Page Refrigeration System Refrigeration System The compressor compresses Ra refrigerant, raising its pressure and temperature.

Refrigerant vapor is pumped out the compressor discharge, down thru the drain pan loop, up thru the condenser coil, around the condenser loop, thru the drier, and into the 3-way valve. By the time the refrigerant has reached the 3-way valve, it has completely condensed into a liquid. Page Operation Overview There is a second compressor delay on power up, Refrigerator Operation but fans will start immediately if cooling is required.

Page 38 Compressor and fan speeds will vary with cabinet Defrost Pre-Chill Single and Variable Speed temperatures until the set temperature is obtained. Compressor After 6 hours of compressor run time door openings After accumulating 32 hours of compressor run time not counted , both the fresh food and freezer will actual compressor run time and door openings , the enter a heated defrost cycle. Page 39 Freezer and Fresh Food Heated Defrost Post Dwell Cycle Following pre-chill, the heated freezer and heated Upon completion of the dwell cycle, the unit will enter fresh food defrost cycle is initiated where both the post-dwell cycle.

The 3-way valve will move to either the A or B The 3-way valve will move to the A position. Page Components Components 5. Disconnect the 3 wire harnesses from the left Note: Throughout this appliance, certain water- side. Lock clips must be reinstalled to prevent leaks. After the water 6.